Car Subwoofers to Home stereo subwoofers?

Speaker Connections for proper impedance match A note about amplifiers: You should always use the recommended load for your amplifier. However, if you must use a load other than the recommended load, here is a short guide. Most solid-state amplifiers would rather look at an open circuit no speaker at all than a load. Therefore, you can usually use a load that is higher than the recommended load. Do not use a lower impedance load, as this could cause serious damage to your SS amp. On the other hand, most tube amplifiers need a load to avoid transformer or tube socket damage. If a mismatch can not be avoided on a tube amp, it is better to go towards a lower impedance rather than too high of a speaker impedance.

Corvette: How to Install an Amplifier

This is necessary when one is adding an amplifier to a factory head unit, since factory head units do not have RCA outputs to get signals from. It consists of a transformer and 10 to 20 watts a high-voltage resistor and connects to amp by using RCA patch cable. The amplifier in the head unit is being loaded by the resistor. It has also an adjustable gain feature to pull output.

Most of the line output converters have wire to ground the transformer.

Depends from the impedance. Lowest allowed is 4 Ohm pro channel. So two 8 ohm speakers parallel results in 4 Ohm and is OK. To have 3 speakers for each channel on 1 connect:amp you can connect 4 Ohm speakers serial, results in 12 Ohm which is allowed, but you will not achieve rated power.

If you use say 2. If you had used 10 mm2 wire you would be down to Basically if you size the wires according to the above table you will be fine. So, if you need a wire to take 7 Amps in a loom then you need only 1 mm2 wire, which is actually the cross sectional area – 1. Note that the bigger wires are made up of a number of smaller wires twisted together. The number of strands will often be more in a car – these tables are normally for domestic wiring which has thicker strands.

The maximum loadings still apply. Wire 5 and 7 core trailer flex is about the best thing around for doing the wiring runs to the front and rear of the car. Standard configuration is rated at 14 Amps and you can get heavy duty rated at 18 Amps. You will rarely need more than 7 wires to the rear of the car, and you can always run two lots of 5 core. Regardless, it prevents having to loom the wires together and can look very neat and tidy.

How to Install Amps and Preamps in Your Home Theater

Wall outlets provide volt AC power, but amplifiers require volt DC power. You’ll have to do a little extra wiring, but the problem is not insurmountable. Look up the input power specifications for your amplifier, using the manual or the manufacturer’s website. Find the specification for current draw in amperes.

Do not use a lower impedance load, as this could cause serious damage to your SS amp. Tube Amps: On the other hand, most tube amplifiers need a load to avoid transformer or tube socket damage. If a mismatch can not be avoided on a tube amp, it is better to go towards a lower impedance rather than too high of a speaker impedance.

These low-frequency speakers deliver. If you want to improve csr sound system in your car, installing one of the best powered subwoofers is a great way to do so. How do i hook up a car amplifier Mail, Phone, Fax orders by personal check allow 14 days for clearancecredit card, or money-order. Amplifier gain controls – setting your gain Bass boost can be very effective but it is rarely ever set correctly. Customers are coming back to us again and again telling us the Boschmann car speaker range produce some serious sound.

Do you already have an account. This is a stereo amplifier kit designed to make use of the [STA] kaida-market. This makes it stronger and less likely to break or leak over time. Got some high powered speakers. You the reader are responsible for anything foolish that you might do as a result of reading this article.

Connect Smartphone to Home Stereo or Car Audio System

By Doug Aamoth January 7, Q: Without spending a fortune, is there a way I can connect my phone to the stereo so I can listen to music? Yes, you absolutely have a few options — some more expensive than others, and one that might actually cost you next to nothing. That thing is looong gone by now, right?

(The simplest way to do this is to run a wire from the amp terminal to Speaker A and then run a second wire from that terminal to Speaker B.) Then the negative terminal of the same amp channel is wired in like fashion to the negative terminals on both speakers.

All it takes is a little know-how and a few tools and supplies. Go to your local car stereo shop and get an amplifier wiring kit. It should have everything you need from cables, wires, fuse and connectors. You need to figure out where you want to put the amplifier. It needs ventilation so most people put it in the trunk or under a seat.

Open the hood and disconnect the negative battery terminal. This will prevent any electrical problems during the hook up of the amplifier and subwoofers. Hook up the power cable. Make sure the fuse is not connected to the power cable.

How do I hook up my Logitech sub to my Kenwood amp in my car?

One thing I learned pretty early in life is that speakers are not meant to be wired together in a haphazard manner. In fact, whenever you plan to connect more than two speakers to a two-channel amplifier — or more than four speakers to a four-channel amp — there are a few things to consider, not the least of which is the amps ability to handle low-impedance loads. Ignoring the basics is like playing Russian roulette with your amplifier: If youre lucky, itll drive the speakers without incident; if youre not, the amp will fry.

I have measured the space where the current amp is (center of the dash at the bottom, behind a storage compartment) and I may need to do a little trimming to make an aftermarket 5-channel fit. The sub would be a long way from the amp but I could fit a decent size box with a port in the location in the back.

How to Install a Car Amp Installing car audio amplifiers is one of the trickiest things a newbie car audio installer can attempt. Car amp installation requires that all sorts of panels be removed and that various wires be run all over the car. Installing car audio amplifiers is a step by step process which I have outlined here. If you have any questions please contact me by clicking here. Please do not attempt a car amp installation if you are not comfortable with the process.

Leave it to a professional. Now here are the steps on how to install a car amp. There is also a wiring diagram below. These directions assume you have already physically mounted your amplifier to a solid, non-conductive surface non-metal. If you have not purchased your power wiring be sure to read this article on choosing wire gauge for amplifiers. Determine what side of the vehicle the battery is on. Disconnect the negative battery terminal.

Easy Aftermarket Amplifier Upgrades

But if you insist on using an amp meter, here’s the information. The most important feature of the amp meter is that it is a low resistance high current device. It must be installed in series with an electrical load to limit current flow. If you were to wire the amp meter directly across the battery as you would with a volt meter the amp meter would immediately pass so much current as to fry the meter, almost instantly. Some amp meters may actually be fused for internal protection.

When properly wired in series with an electrical load the amp meter will monitor the current flowing in the circuit.

You either need to go and buy a car stereo with subwoofer outputs for the rca cable, or you can use your back speakers of your vehicle, you use some regular speaker wire and run it from one of the back speakers to your amp, and use a hookup like an rca hook up 2 plug it into your amp, I did it with my car, but it doesnt sound very well, you can’t control the volume of the subwoofer.

Relax, it’s not difficult at all. Let’s start with the inputs. A balanced connection typically uses XLR connectors, which are relatively large round connectors with three pins male or three holes female in a triangular formation as shown above. This same type of cable used with professional microphones. A balanced connection reduces the risk of induced noise from power cords, radio-frequency interference RFI , and electromagnetic interference EMI.

By the way, if you are going to the expense of a balanced system, make sure it is balanced throughout the amp and not just at the inputs. In a nutshell, here is how a balanced connection works. As I mentioned above, the two signal conductors carry the same signal, but one is out of phase with the other. Any induced noise that is picked up along the cable will be at the same phase in both conductors. At the amp’s input, a differential amplifier recognizes and rejects any signal that is in phase in both conductors, leaving only the intended audio signal.

Using balanced connections can help reduce the risk of ground loops, but only if each device’s ground is properly implemented. However, this is generally not recommended, because you lose any noise rejection and ground-loop isolation. If you must connect balanced to unbalanced, you can use a transformer to isolate all unbalanced connections, as shown above. Various manufacturers, such as Rane , make boxes for this purpose.

Why Car Audio Capacitors Don’t Work

How to install an Amplifier: Disconnect the battery terminals: Run the power cable from the battery to the location of the amp or distribution block. To read more about running wires, click here If you run it through any sort of sheet metal, be sure to protect the power cable with a rubber grommet, or some other protective device.

A separate amp (or amp channel) is necessary when adding a subwoofer to any audio system. AMPLIFYING FACTORY SPEAKERS In most cases you do not want to add an amplifier .

Bass speaker High frequency horn speaker Crossovers handle the separation of sound frequencies, and handle their distribution to speakers. Passive crossovers built into speakers’ cabinets are used in compact music systems. Active crossovers are separate components, and are connected between the sound source a mixer or preamp , and the amplifier.

In professional audio applications, two amplifiers are used to create a bi-amped system. The sound source creates the overall sound signal, and the crossover filters and separates the frequencies. The frequencies are sent to dedicated amplifiers, which are connected to dedicated speakers. Plug a standard shielded connection cable into the mixer’s main output. Consult your owner’s manual or manufacturer’s Web site for specific information.

Plug the other end of the connection cable into the crossover’s input jack. Plug a connection cable into the crossover’s high frequency output jack, and into the input jack of the amplifier that will drive the high frequency horn speaker. Plug a connection cable into the crossover’s low frequency output jack, and into the input of the amplifier that will drive the low frequency bass speaker. Plug the speaker cable into the high frequency amplifier’s speaker output jack, and the other end into the high frequency horn input jack.

Plug the speaker cable into the low frequency amplifier’s speaker output jack, and the other end into the low frequency bass speaker input jack. Set the crossover high and low frequency filters according to your crossover and speaker manual’s recommendations.

Installing an Amplifier & Subwoofer: Geek Squad Autotechs